Skip to content

October 12, 2026 · Exterior · Metro Vancouver

Window Trim Installation in Vancouver: New Windows and Additions

Window trim installation in Metro Vancouver for new windows and additions: matched profiles, sealed joints, interior casings. Insured team. Send a photo for a quote.

Most window trim installation calls we get in Vancouver arrive a few weeks after the windows do. New vinyl units went in during August or September, the old brick moulding came off, the installer filled the gaps with foam and left. Now every opening has a ring of yellow foam and an old paint line where the trim used to sit. Early October, a homeowner in Kitsilano sends us exactly that photo, with the first atmospheric river of the fall in the forecast.

Other versions of the same call: an addition in Coquitlam where the contractor wants trim finished before the painter shows up, or a townhouse complex in Burnaby replacing windows one building at a time.

We install exterior window trim and interior casings for new windows and additions across Metro Vancouver. Here is how the job works and where it usually goes wrong.

New windows still waiting on trim? Send a photo or call (604) 996-0969.

Does a new window need new trim?

Usually, yes. A replacement window rarely has the same frame depth, width or fastening detail as the one it replaced, so the old trim either came off during the install or no longer lines up. Full-frame and new-construction windows always need trim, inside and out. A retrofit window set into the old frame can sometimes keep its trim, but only if that trim is sound and the new frame sits tight against it.

The giveaway is a gap. Foam you can see from the sidewalk.

Spray foam is insulation and an air seal, never meant to face the weather. Left in the sun, it yellows, turns brittle and starts crumbling within a season or two.

Some installers wrap the old wood trim in bent aluminum instead. It looks tidy for a year. Underneath, the wood keeps every bit of moisture it had, and now nobody can see it rot. We would rather take the old trim off and look. If you still have the original trim and want to know whether it can stay, our article on window trim replacement covers the signs that it has to go.

Who installs the window, and who installs the trim?

The window installer sets the window plumb and level, fastens it, and ties it into the wall’s flashing and membrane. Trim comes after that, and that is the part our crew handles: exterior trim, the drip cap over the head, sealant joints, interior casings and paint. On a house with new windows, we usually follow the installer by a few days or weeks. On an addition, we follow the framing and envelope crews.

We do not set windows, and we do not change the size of openings. A bigger opening means a new header, and that is framing work for a contractor, often under a permit. Where that line falls is the same one we describe in handyman vs contractor.

Before any trim goes on, we check what we are about to cover: the window level, the head flashing in place, the membrane lapped top over bottom. If something is off, we photograph it and tell you, so the installer can fix it while it is still clearly their job.

How do you match new window trim to an older Vancouver house?

We measure what is already on the house: the width and thickness of the casing, the shape of the sill nose, the head detail, and the reveal where trim meets frame. Then we build the same profile from stock lumber, or put it together from several pieces when nothing off the shelf matches. Close enough is not good enough on the front of a house. One wrong window reads from across the street.

Metro Vancouver housing makes this interesting. A 1912 Craftsman in Mount Pleasant or Grandview has wide flat casings, a thick sill with ears that run past the sides, and a head piece with its own little cap. A 1970s house in East Van or Burnaby often has narrow brick moulding against stucco. A 1990s townhouse in Richmond might have trim bands or almost nothing.

For material, cedar is our default on the visible trim of an older house, and PVC goes low on the wall where splash-back hits. We cover the tradeoffs in our exterior trim repair article, so we will skip them here. One rule worth repeating: every piece gets primed on all six sides before it goes up, including the back and every cut end.

How is new window trim sealed against the rain?

In layers, and in the right order. The window’s own flashing and membrane do the real waterproofing. The trim sheds water off the face of the wall, a metal drip cap over the head piece carries it past the trim, and sealant closes the joints at the sides and head. The bottom stays open. Seal the sill shut and any water that gets behind the window has nowhere to drain.

That last point is where most homemade trim jobs go wrong. A neat bead of caulk around all four sides looks finished. Then the water the window was designed to let out sits in the sill and soaks the wood from behind.

A few more details that decide how long the job lasts:

  • Weep holes stay clear. Vinyl windows drain through small slots along the bottom of the frame. Trim and sealant never cover them.
  • Sealant goes into a clean, dry gap of a few millimetres. A smear over a hairline crack splits by February.
  • Fasteners are galvanized or stainless. Plain steel nails bleed rust streaks through the paint within two winters, faster near the water in White Rock and Tsawwassen.
  • Two coats of exterior paint over the primer, covering the sealant lines.

Paint is the one step the weather controls. If the rain settles in, the trim stays primed and sealed and the top coats wait for a dry spell.

What changes on the inside when a window is replaced?

The jamb depth usually does. A new window is often thinner or thicker than the old one, so its inside edge no longer lines up with the drywall. We add jamb extensions to bring it flush, then install new casings, plus a stool and apron if the house has them. Drywall that got chipped during the window install gets patched and painted on the same visit.

Newer houses mostly have picture-frame casing, the same profile on all four sides. Older ones usually had a stool, the interior sill you set a plant on, with an apron under it. We match whichever the house has.

A note on MDF. It is fine for side and head casings in a bedroom. We do not use it for the stool. Wet-coast windows run with condensation on cold January mornings, and MDF that soaks up water at a cut edge swells and never goes back. Solid wood or PVC on the stool, and on anything in a bathroom.

How does trim installation work on an addition or a strata window project?

On an addition, window trim is one of the last exterior steps: after the windows, flashing and membrane are in, and before the painter. On a strata window replacement, it runs unit by unit behind the installer. Either way, we work from the contractor’s or property manager’s schedule, match the trim already on the building, and finish each unit’s openings before moving to the next one.

Additions are where a mismatch shows most, because trim a little narrower than the original house gives the new wing away. We measure from the old windows, not the drawings.

Strata projects add paperwork. The council approves the profile and colour, owners get notice before we come in for interior casings, and property managers often ask for proof of liability insurance. We carry it and send the certificate when asked.

What we look at on a window trim estimate

A few photos answer most of it. Send them through our booking page: one of the whole window from outside, a close-up of a corner, one of the inside, and one of an existing window on the house whose trim you want copied. From those we look at:

  • How many windows, and whether it is exterior trim, interior casings or both.
  • Height and access. A ground-floor window is quick to reach. Second-storey windows may need scaffolding.
  • The profile. Flat stock trim is straightforward. A built-up Craftsman detail takes more cutting and fitting.
  • Jamb extensions, stools and drywall touch-ups on the inside.
  • Paint, and whether you have the colour code or need a match.

Those are the things that affect the cost, and we quote after seeing them. Window trim installation and replacement sit with exterior trim, drywall and paint in our services.

Book a free on-site or photo estimate at 604hm.com/booking, or call (604) 996-0969. We install window trim in Vancouver, Burnaby, Richmond, Coquitlam, North Vancouver, Surrey, White Rock and across Metro Vancouver.

Frequently asked questions

Can you install trim around vinyl windows?

Yes, most of the windows we trim are vinyl. The rule is to fasten the trim to the wall framing, not through the vinyl frame, because vinyl moves more with temperature than wood does. We leave a small sealant gap at the frame so the window can expand and contract on a hot afternoon without splitting the caulk line or pushing the trim out of square.

How long does it take to install trim on new windows?

It depends on how many windows there are and how high they sit. A single ground-floor window with exterior trim and interior casings is typically part of a day. A house with eight or ten new windows usually takes our crew two to three days, plus drying time between primer, sealant and paint. Second-storey windows that need scaffolding add setup time.

Do I need a permit for window trim installation in Vancouver?

Trim on its own usually does not need one. Permits come up with the windows themselves when an opening changes size, and with additions, which almost always need a building permit. That question sits with the window installer or the contractor running the project. Rules differ between Vancouver, Burnaby, Surrey and the other municipalities, so check with your city if you are not sure.

Can new window trim be installed in the rainy months?

Yes. Cutting, fitting and fastening go ahead in most weather, and every piece is primed on all sides before it goes up, so it can sit through a wet spell. What waits for a dry day is sealant and paint, which need a dry surface and temperatures above the minimum on the label. From November to March we plan those steps around the forecast.

Call Book online