Skip to content

November 20, 2026 · Kitchens · Metro Vancouver

Kitchen Sink Replacement in Vancouver: What We Swap and Seal

Vancouver kitchen sink replacement: drop-in and undermount swaps, resealed rims, new faucets and drain parts. Insured, owner-led team. Send a photo for a free estimate.

Kitchen sink replacement in Vancouver usually starts with a damp towel. In the second half of November the kitchen works harder: roasting pans soak overnight, the dishwasher runs twice a day, and someone reaching into the sink base for a garbage bag finds the cabinet floor wet. Our crew opens that cabinet in Burnaby condos, Coquitlam split-levels and East Vancouver houses every winter. Sometimes the leak is a tired seal and the sink stays. Sometimes the sink itself is finished.

If the sink is one of several things to fix before guests arrive in December, our holiday repair list covers the rest.

Water under the kitchen sink? Send a photo or call (604) 996-0969.

When does a kitchen sink need replacing instead of repairing?

Replace the sink when the bowl itself has failed: a crack through a fireclay or composite bowl, enamel chipped through to rusting cast iron, stainless pitted or dented around the drain, or an undermount sink sagging off broken clips. A drip at the rim, the drain basket or the trap is usually a repair. We check those parts first, because a new sink does nothing for a leaking trap.

Where the water shows up says a lot. A dark line on the cabinet wall right under the rim means the seal between sink and counter has let go. Drips from the drain basket mean dried-out putty. Water on the slip nuts of the trap is usually a flattened washer, and that one takes minutes.

An undermount sink that has dropped a few millimetres away from the stone needs attention soon. The silicone line has broken, every rinse runs down the gap into the cabinet, and the bowl hangs on whatever clips are left. Until it is fixed, keep heavy pots out of it.

Being tired of a shallow double bowl that will not take a roasting pan is a fair reason too. The swap is the same job.

What does a kitchen sink swap include?

A like-for-like swap means the new sink goes in the same spot, on the same drain and supply lines. Our crew shuts the water at the valves under the sink, disconnects the faucet lines, the trap and the dishwasher hose, cuts the old seal, and lifts the sink out. Then we clean the cutout, check the cabinet below, set the new sink, seal it and reconnect everything.

The parts that go back in new on every swap:

  • Basket strainers, with fresh putty, or silicone where the sink maker calls for it.
  • Trap washers and slip nuts. The old ones have taken the shape of the old pipes.
  • Braided supply lines to the faucet, even when the faucet itself stays.
  • The dishwasher drain hose, run in a high loop or through the existing air gap, so sink water cannot flow back into the dishwasher.

Before the new sink goes in, we look hard at the cabinet floor. A soft, swollen sink base gets dried out and rebuilt first, and our notes on kitchen cabinet repair explain why closing it up wet starts the cycle again.

The last step is a water test. We fill the bowls, pull the plugs together and run a dry paper towel around every joint, which shows a drip long before a puddle does.

Can a drop-in sink be replaced with an undermount?

On a stone, quartz or solid-surface counter, yes, with a stone fabricator cutting and polishing the new opening. On a standard laminate counter we advise against it. Laminate has a particleboard core, and an undermount leaves the cut edge of that core exposed to water from every rinse. Within a few years the edge swells and the laminate lifts. A new drop-in suits laminate better.

Drop-in to drop-in has its own rule: the new rim has to cover the old hole. A laminate cutout can be made bigger with a jigsaw. It can never be made smaller. So we measure the opening itself and check it against the cutout template that comes with the new sink. A 33-by-22-inch double bowl is a standard North American size, and plenty of new sinks drop straight into that opening.

When we enlarge a laminate cutout, we seal the fresh edge before the sink goes in, because raw particleboard next to a sink soaks up steam and splash.

Undermount to undermount on stone is heavier work: we support the old bowl from below, cut it free of its clips and silicone, clean the stone back to bare and hang the new one on fresh clips.

How do you seal a kitchen sink so the cabinet stays dry?

With 100% silicone rated for kitchens, on surfaces stripped back to bare. Old silicone has to come off completely, because new silicone does not bond to old. A drop-in sink gets a continuous bead under the rim, and the clips underneath are tightened evenly so the rim sits flat. An undermount gets silicone between the bowl lip and the stone, held tight by clips while it cures.

Clip pressure decides whether the bead does its job. Crank one corner tight and the rim lifts at the opposite one, leaving a gap the silicone has to bridge alone. We work around the sink in rounds, a little at a time, the way you tighten wheel nuts. A cast-iron drop-in has no clips at all; its own weight presses the rim into the silicone.

Silicone skins over in minutes and takes about a day to cure fully, so after our crew connects the faucet and trap, the sink stays dry until morning.

Which parts of a kitchen sink replacement need a licensed plumber?

Anything that changes the pipes in the wall or floor. Moving the sink, adding a drain or a vent, replacing seized shut-off valves, or lowering the drain because a deeper bowl no longer lines up with it all go to a licensed plumber, with a permit where the city requires one. A new garburator that needs its own circuit goes to a licensed electrician. We swap the sink, faucet and trap on the existing connections.

The deep-bowl problem catches a lot of people. A new sink with a 10-inch bowl puts its drain outlet two inches lower than the 8-inch sink it replaces. If the drain comes out of the wall high, the trap would have to sit lower than the pipe it drains into, and water does not run uphill. We measure the drain height in the wall before you order a deeper sink.

Shut-off valves are the other common stop. Plenty of kitchens from the eighties and nineties still have multi-turn valves nobody has closed since they went in, and after decades they refuse to close or start weeping at the stem. Then we stop. A plumber replaces the valve before the sink comes out. Our handyman vs contractor guide shows where the same line falls on other jobs.

What changes when the sink is in a strata condo?

Mostly the logistics around the water. Many condos have shut-off valves under the sink, but in some older buildings the nearest valve serves a whole stack of units, and the building manager has to schedule the shutdown with notice to the neighbours. Strata bylaws set contractor hours and elevator bookings. A leak in a condo sink base also travels: it can end up in the ceiling of the suite below.

So before we book a sink swap in a West End tower or a Metrotown highrise, we ask where the nearest shut-off is and whether the building needs the shutdown arranged. The old sink leaves with our crew.

What we look at on a sink estimate

Most sink jobs can be scoped from photos sent through our booking page:

  • The sink and counter from above, with the whole cutout in frame.
  • Inside the sink base with the doors open: valves, trap, dishwasher hose and the cabinet floor.
  • A close-up of the counter edge at the rim, where laminate swells first.
  • The new sink’s model number, if you have one.

If you have not bought it yet, send the photos first. We can tell you which sizes fit the opening and how deep a bowl the drain height allows, before you pay for a sink that will not fit.

What affects the cost is the sink type and counter material, whether the cutout changes, whether the faucet is new, the state of the shut-offs and the sink base, a garburator or dishwasher to reconnect, and access in a strata building. Sinks, vanities, cabinets and tile are all part of the kitchen and bathroom work in our services. Most like-for-like swaps take one visit.

Book a free on-site or photo estimate at 604hm.com/booking, or call (604) 996-0969. We handle kitchen sink replacement in Vancouver, Burnaby, Richmond, Coquitlam, Surrey, North Vancouver, New Westminster and across Metro Vancouver.

Frequently asked questions

How long does it take to replace a kitchen sink?

A like-for-like drop-in swap with the faucet usually takes our crew a few hours. Undermount sinks take longer, because the old bowl has to be cut free and the stone cleaned back to bare. In both cases the silicone needs time to cure, so plan on leaving the sink dry until the next morning. Changing the size of a stone cutout adds a separate visit from a fabricator.

Can I keep my old faucet when the sink is replaced?

Often, yes, if it works well and suits the hole layout of the new sink. A single-hole faucet on a sink with three holes needs a deck plate to cover the extra ones. We fit new supply lines either way. If the faucet already drips or the handle is stiff, replacing it while everything is disconnected takes less labour than a second visit later.

Will a new kitchen sink fit the hole in my countertop?

For a drop-in sink, the new rim has to cover the existing cutout with some overlap on every side. Measure the opening in the counter and compare it with the cutout template for the new sink, because the outer rim of the old sink tells you little. Laminate openings can be cut larger, never smaller. On stone and quartz, any change to the opening is a fabricator's job.

What should I clear out before the crew arrives?

Empty the sink base completely, including the garbage bin and cleaning products, and clear the counter for about an arm's length on each side of the sink. Run the dishwasher the night before so it is empty when we disconnect the drain hose. In a condo, tell us where your shut-off valves are and book the elevator if the building requires it.

Call Book online